GamesConsole Types

What Are You Shopping For?

Drill

Brand New STAR Gas Hammer Drill with 1 Drill Capacity, 3 Functions, SDS-PLUS

Brand New STAR Gas Hammer Drill with 1" Drill Capacity, 3 Functions, SDS-PLUS


Gasoline Hammer Drill, 3functions, SDS-PLUS Engine: 1E34F-R, Single Cylinder, Air Cool, 2 Stroke Displacement: 25.4cc Max. Output power: 0.7Kw/7500rpm No-load Speed: 900r/min Percussion Rate: 4800/min Tank Capacity: 0.6 cord Max Drill Capacity (Diameter): 1.18" Overall Size: 20*9*9.4" Chuck Plug Out/Insert In function. Can be replaced with drill chuck. Packing: BMC with Accessories: 0.2/0.3/0.4"x6" SDS PLUS drills; 0.55x10" SDS PLUS Flat & Point Chisel, 0.5" Chuck Approval: CE/EPA Prostar Equipment Inc. exclusivelly distribute STAR concrete & masonry power equipments & tools. Prostar Equipment Inc. manufactures and distributes same name PROSTAR diamond blades, cut off wheel, wood blade, rebar cutter&benders and bolt cutter. Welcome to visit official website www.prostarequipment.com for more items. All are in stock and could be shipped immediately after payment cleared.
more at Amazon Marketplace		Amazon Marketplace
store rating : 2.75		Only $799.00
Compare prices
Cleveland 2075A Cobalt Steel Jobbers' Length Drill Bit, TiAIN Coated, Round Shank, 135 Degree Notch Point, 5/16 (Pack of 5)

Cleveland 2075A Cobalt Steel Jobbers' Length Drill Bit, TiAIN Coated, Round Shank, 135 Degree Notch Point, 5/16" (Pack of 5)


The Cleveland 2075A wide land, parabolic, jobber-length drill bit is made of cobalt, has 135-degree notched-point geometry and TiAlN surface treatment, and is suitable for deep hole drilling with precision holes. This series has higher speeds and feeds for increased productivity over standard drill bits. The round shank diameter is the same as the drill size. The 2075A series has a wide land parabolic flute design that enhances chip removal. The coolant has a better flow to the drill point for heat dissipation, and can be used at higher speeds and feeds for increased productivity. The TiAlN coating resists heat better than TiN and TiCN coatings, helping increase tool life and performance. It also has increased hardness compared to TiN and may reduce the need for lubricants based on the application. The wider land increases the torsional strength of the drill which increases the hole tolerance for high precision work. This series of drill bits are suitable for drilling into stainless steel, carbon steel, cast iron, aluminum, brass, plastic and nickel alloys. The spiral flutes act as a passageway for chip removal. The right-hand twist brings chips up and away from the cutting edge. The jobber length offers a good compromise between reach and rigidity. The inch sizes are manufactured to American National Standards Institute (ANSI) specification and metric sizes are manufactured to Deutsches Institut für Normung (DIN) 338 specifications. The 135-degree notched-point drill geometry ensures a more accurate hole by reducing walking when the hole is started. The notched point can withstand higher thrust loads, like those encountered when drilling tough alloys, than conventional point geometry. The tolerances for various aspects of the Cleveland drill bits are: drill diameter range 0” to 1/8” +0.0000”/-0.0005”, over 1/8” to 1/4” +0.0000”/-0.0007”, over 1/4” to 1/2” +0.0000”/-0.0010”, over 1/2” to 1” +0.0000”/-0.0012”, over 1” to 2” +0.0000”/-0.0015”, over 2” to 3 1/2” +0.0000”/-0.0020”; drill overall length and flute length #80 through 1/8” +0.1250”/-0.0626”, over 1/8” to 1/2” +0.1250”/-0.1250”, over 1/2” to 1” +0.2500”/-0.1250”, over 1” to 2” +0.2500”/-0.2500”, over 2” to 3 1/2” +0.3750”/-0.3750”; drill point angle diameter range 1/16” to 1/2” included angle 118 or 135 degrees +/-5 degrees, over 1/2” to 1 1/2” included angle 118 degrees +/-3 degrees, over 1 1/2 to 3 1/2 includes angle 118 degrees +/- 2 degrees; drill lip height diameter range 1/16” to 1/8” total indicator variation 0.0020”, over 1/8” to 1/4” total indicator variation 0.0030”, over 1/4” to 1/2” total indicator variation 0.0040”, over 1/2” to 1” total indicator variation 0.0050”, over 1” to 3 1/2” total indicator variation 0.0060”. Drill bits are cutting tools used to make holes in a range of materials. They are used in machines such as handheld portable drills, drill presses, machining centers, and lathes. Drill bits come in a variety of types and lengths. Twist drill bits are the most common type of drill bit. They are a round, twisted shaft, end-cutting tool with two or more cutting edges and two or more flutes. Jobber drill bits are the most common length of twist bit. They offer a good comprise of length and reach to work with the widest range of materials and applications. Greenfield Industries manufactures tools under the brand names Cleveland, Chicago-Latrobe, Cle-Line, Vermont Tap & Die, Bassett, Putnam Tools, Geometric, Vers-O-Tool, H & G, and Acme-Fette. The company, owned by Top-Eastern Group and headquartered in Seneca, SC, makes tools that meet American National Standards Institute (ANSI), National Aerospace Standard (NAS), and Deutsches Institut für Normung (DIN) standards.
more at Amazon		Amazon
store rating : 3.43		Only $103.40
Compare prices
Carbide Center Drill #1 Carbide Center Drill

Carbide Center Drill #1 Carbide Center Drill


If none of the common methods for removing a frozen screw work, and drilling is in order, these carbide center drills should be used to center and "start" the hole. With the spindle at fairly high speed, bring the center drill down to the screw head and adjust position until centered in the screw. Apply pressure and cut until center hole is deep enough to allow the proper undersized, regular drill bit to start cutting without catching on the screw head slot. Better for drilling broken taps too, for they will cut center holes in even the hardest ones. And, because of the large body mass of the tool relative to the small drill diameter, it is very sturdy and rigid. Mfg: Brownells SPECS: #1, .125 body/.0468 drill; #2, .187 body/.0781 drill; #3, .250 body/.1093 drill; #4, .312 body/.1250 drill.
more at Brownells		Brownells
Only $20.99
Compare prices
#12-14 x 3/4 Hex Self Drill Screws

#12-14 x 3/4" Hex Self Drill Screws


You have probably seen them before. The fellow that installed the ductwork for your furnace or air-conditioner probably used them. You may have even used them when putting something together that said on the box Some Assembly Required. They are called self drilling screws and are they ever handy! A special point drills through the steel sheet metal quickly then the hardened steel threads self-tap the hole and pull everything together securely. Zinc plated and stress relieved for strength. 5/16 Hex Head. #3 Point size will drill and tap a combined materail thickness of .110" to .210". Made in Taiwan.
more at McFeely's		McFeely's
Only $139.76
Compare prices
Mill/drill,14 In,3/4hp,110v,115-2600 Sp - DAYTON

Mill/drill,14 In,3/4hp,110v,115-2600 Sp - DAYTON


Mill/drill Machine, Swing 14 In, Motor Hp 3/4, Voltage 110, Spindle Taper R8, Spindle Speeds 115-2600, Spindle Travel 3 1/2 In, Spindle To Table 14 In, 9/16 T-slots, Capacity 1 In Drill, 1/2 In End Mill, 2 1/2 In Face Mill, Includes 1/2 In Chuck, 2 1/2 In Face Mill Cutter W/arbors, R8/mt3 Arbor Adaptor, Work Light, 6 Piece R8 Collet Set 1/8 To 3/4 X 8ths
more at Grainger		Grainger
Only $2098.00
Compare prices
All Star Allstar Marketing HT011712 Half Time Drill Driver

All Star Allstar Marketing HT011712 Half Time Drill Driver


more		 $8.97 - $119.94
from 9 stores
Compare prices
Drill Doctor SEPTLS244DD350X - Drill Bit Sharpeners

Drill Doctor SEPTLS244DD350X - Drill Bit Sharpeners


more		 $69.34 - $69.34
from 2 stores
Compare prices
General Tools 825 / Drill Grinding Attachment

General Tools 825 / Drill Grinding Attachment


more		 $33.97 - $35.99
from 3 stores
Compare prices
Ingersoll Rand Ingersoll - Rand 1/2

Ingersoll Rand Ingersoll - Rand 1/2" Reversible Industrial - Duty Design Air Drill


Ingersoll Rand Ingersoll - Rand 1/2 Reversible Industrial - Duty Design Air Drill rating
more		 $176.42 - $282.75
from 13 stores
Compare prices
Fiskars 8516 Green Craft Hand Drill

Fiskars 8516 Green Craft Hand Drill


Fiskars 8516 Green Craft Hand Drill rating
more		 $12.91 - $14.84
from 2 stores
Compare prices
Drill Doctor Diamond Replacement Wheel

Drill Doctor Diamond Replacement Wheel


more		 $14.49 - $41.19
from 13 stores
Compare prices
Dewalt Dd5060 Impact Drilling Set, 10 Piece

Dewalt Dd5060 Impact Drilling Set, 10 Piece


more		 $24.72 - $44.99
from 10 stores
Compare prices
Metric Drill Bit 4.50 Mm By Hanson Made In The Usa

Metric Drill Bit 4.50 Mm By Hanson Made In The Usa


more		 $7.95 - $7.95
from 2 stores
Compare prices
Powerglide& 12 Volt Drill Charger

Powerglide& 12 Volt Drill Charger


more		 $11.49 - $11.49
from 1 stores
Compare prices
Next Generation Power Engineering 3/8

Next Generation Power Engineering 3/8" Close Quarters Drill


more		 $29.99 - $89.99
from 2 stores
Compare prices
Drill Doctor DD350X Drill Bit Sharpener

Drill Doctor DD350X Drill Bit Sharpener


more		 $49.95 - $79.95
from 17 stores
Compare prices
Wolfcraft 4525 Drill Guide Attachment for 1/4-Inch or 3/8-Inch Drills

Wolfcraft 4525 Drill Guide Attachment for 1/4-Inch or 3/8-Inch Drills


more		 $23.08 - $47.99
from 4 stores
Compare prices
DEWALT DW130V Heavy-Duty 9 Amp 1/2-Inch Drill with Spade Handle

DEWALT DW130V Heavy-Duty 9 Amp 1/2-Inch Drill with Spade Handle


more		 $149.00 - $260.99
from 13 stores
Compare prices
Master Heaters 1/2

Master Heaters 1/2" Heavy Duty Variable Speed Reversible Drill


more		 $29.99 - $29.99
from 1 stores
Compare prices
Next Generation Power Engineering 1/2

Next Generation Power Engineering 1/2" Heavy Duty Low Speed Drill


more		 $44.99 - $149.00
from 3 stores
Compare prices
drill : end search Power by shopping.com


What Are You Shopping For?

All Right Reserved By VideoConsoleGames.com All Your Cheapest Video Games Console Systems.